Shield Plumbing repairs and replaces faucets, sinks, toilets, shut-off valves and garbage disposals for homes in Kannapolis, Concord, Harrisburg and Mooresville.
A dripping faucet, a running toilet or a stuck shut-off valve wastes water every day. Most fixture problems come down to a worn part, such as a washer, cartridge or flapper. We find which part failed, tell you whether a repair will last, and replace the fixture only if it makes sense.
Fixture problems usually start small. Here are the signs worth a call.
If a faucet drips, a toilet keeps running or a shut-off valve is stuck, call Shield Plumbing about faucet and fixture repair. Call (980) 980-9219
Fixtures are the parts of your plumbing you touch every day, so they wear the fastest. Small leaks are easy to ignore, but they add to your water bill and can damage cabinets and floors. Many problems need only a new part. Others are a sign the fixture is near the end of its life.
| Job | Typical time |
|---|---|
| Faucet repair | About 1 hourTypical for a new washer or cartridge. |
| Toilet repair | About 1 hourFlapper, fill valve or wax seal replacement. |
| Faucet or toilet replacement | 1 to 2 hoursDepends on access and the condition of the valves. |
| Shut-off valve replacement | 1 to 2 hoursMay require turning off water to the house. |
Fixture repair cost depends on what failed and whether you supply the new fixture. Replacing a washer or flapper is a small job. Swapping a whole faucet or toilet takes more time. You get an estimate before any work starts, and we tell you if a repair is not worth it.
| Factor | How it affects the price |
|---|---|
| Repair or replace | A new part costs less than a whole new fixture. |
| Who supplies it | You can buy the fixture, or we can source the parts. |
| Valve condition | Seized shut-off valves may need replacing before the fixture. |
| Access | Tight cabinets and old fittings can take longer to work on. |
| Number of fixtures | Several small repairs on one visit can save a second trip. |
We check whether a washer, cartridge, seal or valve has failed.
We tell you if a repair will last or a new fixture makes more sense.
We test the shut-off valves, since a stuck valve makes future repairs harder.
We run the fixture, check every connection for drips, and clean up the work area.
Call and tell us what is going on. You get an estimate before any work starts.
Many Harrisburg and Mooresville homes were built in the last few decades with builder-grade faucets and toilet parts. Those parts often wear sooner than better-quality ones. When a faucet drips again soon after a repair, a better replacement can save repeat calls.
Older homes in Kannapolis and Salisbury bring different problems. Shut-off valves may not have been turned in years and can seize or leak when finally used. Old supply lines and fittings can be hard to free. We check them before starting, so a simple faucet swap does not turn into a surprise leak.
If the faucet is in good shape and parts are available, a new washer or cartridge usually fixes the drip. If the body is corroded, parts are hard to find, or it drips again soon after a repair, replacing the faucet often costs less over time. A plumber can tell which applies.
A running toilet usually has a worn flapper or a faulty fill valve. The flapper is the rubber seal at the bottom of the tank. When it no longer seals, water leaks into the bowl and the tank keeps refilling. Both parts are quick to replace in most homes.
Turn off the switch and unplug it or shut off the breaker first. Never put your hand inside. Many units have a reset button on the bottom. If it still hums without spinning, something is jammed or the motor is failing. A plumber can clear it or replace it.
More than most people expect. A steady drip can add up to many gallons a week, and it shows up on your water bill. It also leaves mineral stains and can wear the sink finish. Most drips come from a worn washer or cartridge, which is a small repair.
Yes. Many homeowners pick their own fixture. Choose one that fits your sink holes or toilet rough-in, the distance from the wall to the drain. If you are unsure, send us the model before you buy. We will tell you if it fits your setup.
Common causes are a loose supply line, a cracked drain trap, a worn faucet seal or a failing shut-off valve. Dry the cabinet, then run water and watch where drops form. If you cannot find it or it keeps leaking, shut off the valve and call a plumber.
Signs include water around the base after flushing, a sewer smell near the toilet, a toilet that rocks, or a stain on the ceiling below an upstairs bathroom. Replacing the wax ring means lifting the toilet off the floor, so it is worth having a plumber do it.
Yes, once or twice a year. Turn each valve under your sinks and toilets off and back on. If one is stuck, leaks or does not stop the water, have it replaced. You want working valves before a leak, not during one.
Call to describe the problem. You get a clear plan and an estimate before any work starts.
